Auto diagnostic tool: 十月 2012

2012年10月30日星期二

Auto diagnostic tool

How to Troubleshoot a VW Engine Light 1Open the fuse panel cover underneath the steering column cover. Turn the knob on the fuse cover counterclockwise to unlock it and pull the fuse cover off the fuse panel.2Locate the port for the OBD tool.

There exists only 1 port large adequate to accommodate the OBD tool on the fuse panel Auto diagnostic tool.3Plug the electrical connector on the OBD tool into the port on the fuse panel.4Turn the ignition essential to the "II" position. Wait for the ODB pc to send a signal for the OBD tool car diagnostic software.

A code are going to be generated on the display screen on the OBD tool. You may ought to seek the advice of your VW vehicle's service manual for the error codes to understand what the precise concern or difficulty is. Each and every VW automobile model may possibly have distinctive error codes determined by the year in the car along with the selections equipped on the vehicle.

2012年10月28日星期日

automotive diagnostic tools

The way to Troubleshoot a Mazda Millennia 1Locate the onboard diagnostic port of the Millenia by feeling around the spot below your steering wheel. The port is going to be located in the prime in the driver's side foot effectively and might or may possibly not have its personal spot in the dashboard material, based on the year of the Millenia.2Plug the code scanning tool into the onboard diagnostic port, then engage the ignition of the Millenia in order that its electronics program is activated.

You could either turn the ignition on each of the way or to just the accessories position, which is promptly prior to the engine ignition.3Allow the code scanner to scan the diagnostic system for any error codes Auto diagnostic tool. Take note of any codes that are displayed by the code reader. Decode the error codes by performing a search on the net GM MDI, cross-referencing them having a book of doable diagnostic codes, or by bringing the codes to a mechanic or dealership.

Tips on how to Troubleshoot a Ford Transmission Personal computer 1Locate the open OBD port on the left side in the Ford's fuse panel inside the driver's-side foot effectively.2Plug the OBD tool in to the open port (there is only 1 that is certainly massive adequate).3Turn the ignition for the "II" position and wait for the scan tool to retrieve the error code. This numeric code can then be used to determine what is wrong with your Ford's transmission. You will need your Ford vehicle's service manual to translate the code.

Auto diagnostic tools Com.&quot

Tips on how to Test Continuity With an Actron Multi-Tester 1Plug the leads into the tester. The red ideal tester plugs in to the hole labeled "VΩmA." The black right tester plugs into the hole labeled "Com Auto diagnostic tools."

2Disconnect the power source of the circuit to be tested for continuity.3Turn the selector switch in the center of your Actron Mulititester and align the dot on the switch with the "200" in the green "Ω" section.4Press and hold the red lead to the positive side of the circuit to be tested for continuity and the black lead to the negative side of the circuit.

5View the multitester's LED display for an ohm reading. If the ohm measurement is low, then your circuit has good continuity automotive diagnostic tool. If the measurement is high, then your circuit has low continuity.

Obd2 scanner

How you can Test & Keep Mechanics Tools 1Choose the type of mechanic's tool that you want to test and purchase it. For instance Obd2 scanner, you could get a set of wrenches, a pneumatic lug wrench or even an oil filter wrench.

2Use the tool. If you're testing a lug wrench then use it to loosen and tighten the lugs on a wheel of your car. If you're using a set of wrenches then use them to take off properly sized bolts in your car. If the tool breaks, is too big or small or they just don't function properly then chances are the tool you're using isn't right for your collection.

3Place the tool in a safe, dry place. All tools, whether hand tools or power tools Car Diagnostic Tools, should be cleaned and dried before they're put away in a safe place like a tool drawer inside a garage or basement. Dankness can rust tools and rot rubber. Once you find a tool that works for you take care of it properly so it will last for a long time.

2012年10月24日星期三

Auto diagnostic tool Start&quot

Ways to Troubleshoot a Ford Automatic Transmission 1Park your Ford vehicle on a level surface. Begin your Ford and let it to idle for two to 3 minutes.2Open the hood of one's Ford and pull on the looped manage that sits behind the engine. The manage ends at a extended neck that stretches down towards the transmission. That is the transmission dipstick.3Remove the dipstick totally, wipe it off then reinsert it all the way into the filler neck till it bottoms out auto diagnostic software. Then remove it once more. Note the color. It ought to be reddish. If it is not, the transmission fluid could possibly be burned Auto diagnostic tool. Confirm this by smelling the fluid. If it smells burned, it truly is. You can want to alter your transmission fluid quickly to stop additional harm to your transmission. The fluid level need to also be in between the upper and decrease fill marks on the finish on the dipstick. If it is actually low, you require to fill the transmission with Ford-approved automatic transmission fluid.4Check for complications staying in gear although driving. If the vehicle slips out of gear whilst driving, this indicates a problem together with the transmission. You could possibly also hear grinding or crunching noises. This indicates that your transmission is seriously damaged and demands an overhaul.5Check for transmission complications employing an on-board diagnostic scan tool. This tool could be plugged into the OBD access port situated for the left in the fuse panel beneath the dash within the driver's side footwell. Press "Start" on the scan tool or wait for the tool to automatically retrieve the error codes. You could then have these codes translated utilizing your Ford's service manual or by most auto parts stores.

Vehicle Diagnostic equipment

How you can Retrieve the DTC From the Gem Module of a 1995 Ford 1Park the car on a flat surface and shift the car into 1st gear (should you have a common transmission) or park (if you have an automatic transmission) and turn off the engine.

Apply the parking brake and turn the ignition back for the "On" position without starting the engine.2Plug an automotive scan tool in to the vehicle's diagnostic data port. This port is mounted underneath the driver's side dashboard region.3Power on the scan tool and choose " Vehicle Diagnostic equipment;GEM" from the primary menu.

Decide on "Codes" from the GEM sub-menu. Then pick out, "Read all current and stored DTCs."4Write down the DTCs displayed on the scan tool's screen Professional diagnositic tools.

2012年10月22日星期一

auto diagnostic software

Ways to Reset the SRS on a Honda Civic 1Find the diagnostic port that is definitely the same size and shape because the scan tool's connective end.

This diagnostic port is often found on the underside on the driver's side dash subsequent for the steering column.2Plug the scan tool into this diagnostic port. Put the crucial into the ignition and turn it to the "ACC" auto diagnostic software; position, but don't start out the engine automotive diagnostic tool. This ought to turn on most scan tools. If yours does not turn on, find the on/off switch on the tool.

Wait for the OBD scan tool to read the codes.3Find the "Erase Codes" command and choose it. Wait for the tool to finish the job.4Unplug the OBD tool and start the engine. Verify all lights have turned off on the instrument cluster.

2012年10月21日星期日

Obd2 scanner selection using the arrow keys on the scan tool. Decide on &quot

Tips on how to Reset the Fuel Program on a 1999 Jeep 1Park the Jeep on a flat surface and turn off the engine. Turn the ignition so that it clicks the moment, but does not commence the engine.

This can be the "run" position and it is going to illuminate the dashboard.2Locate the vehicle's diagnostic information port underneath the dashboard on the driver's side, above the pedal spot Obd2 scanner. Connect an automotive scan tool for the Jeep's diagnostic information port and turn on the scan tool diagnostics car tool.3Notice the main menu on the scan tool.

Select the "PCM" selection using the arrow keys on the scan tool. Decide on "Clear all existing and stored DTCs" from the PCM menu. Wait a moment when the scan tool clears the DTCs.4Unplug the scan tool from the car. Begin the engine and check to find out if the "Service Car Soon" light is on. If this light is turned off, the fuel method is reset.

2012年10月19日星期五

auto diagnostic

How you can Reset the Code on an Infiniti 1Locate the OBD port on the driver's side dash underneath the steering column. Plug the OBD scan tool into this port.

Don't force it in for the reason that you might bend the pins inside Auto diagnostics.2Put the key into the ignition and turn it towards the "on" position, taking care not to start the engine.3Wait whilst the scan tool interfaces together with the laptop. Select "Delete Codes" or maybe a equivalent command to erase the codes and reset the computer system.

Wait till the scan tool indicates that it has completed the task auto diagnostic.4Unplug the scan tool from the port and start the engine. Verify that all warning and service lights have shut off.

Car Diagnostic Tools 4Press &quot

How to Reset the 1997 Volkswagen Verify Engine Light 1Locate the diagnostic port on the dashboard beneath the heater control panel. The port is the exact same size and shape because the connector on the diagnostic code scanner. Plug the scanner into the port.

2Put the essential into the ignition and turn the important to " Car Diagnostic Tools;Run automotive diagnostic tool." Don't start out the engine. This can energy on the diagnostic code scanner automatically.3Push a button that reads "Scan Codes" (or equivalent) in your diagnostic code scanner. Wait whilst the scanner completes its work. It will list the difficulty codes on the face with the scanner.

4Press "Clear Codes" or "Delete" (or equivalent) on the diagnostic code scanner. When the scanner returns for the menu screen or displays a message to indicate the codes happen to be cleared, unplug the scanner from the port.5Turn the automobile off and wait a couple of minutes. Turn the engine on and examine the instrument panel. The verify engine light should now be off.

car diagnostic tool 2Plug the electrical connector on the on-board diagnostic

Tips on how to Reset an Olds "Service Engine Soon" Light 1Open the fuse panel cover under the steering column by prying down on it with your fingers.2Locate the fuse for the electronic control unit, or ECU, using the fuse diagram on the underside of the fuse panel cover.

3Pull the fuse for the ECU using the fuse pullers mounted in the fuse panel.4Turn the ignition to the "II" position and wait five minutes before reinserting the fuse.5Wait for the "service engine soon" light to go out on the dash. Tips on how to Reset an SRS Light on an Acura MDX 1Open the fuse panel, and remove the fuse panel cover by pushing the release levers toward one another (on either side of your fuse panel cover) and pulling the cover down diagnostic car tool.

2Plug the electrical connector on the on-board diagnostic (OBD) reset tool into the fuse panel car diagnostic tool. There is only one electrical input port big adequate for the diagnostic tool.3Turn the ignition important to the "II" position, and wait for the SRS light to become reset.

car diagnostic software PCM&quot

The way to Reset a GM PCM 1Shift the vehicle's transmission into park or first gear. Shut down the engine and set the parking brake car diagnostic software. Rotate the ignition back to the "On" position but do not begin the engine.2Plug the scan tool's data cable into the vehicle's diagnostic information port, located underneath the dashboard on the driver's side.

3Turn on the scan tool and allow it to boot up. Comply with the on-screen instructions to enter inside the vehicle's particular drivetrain information and facts.4Select "PCM" from the scan tool's major menu. Pick out "codes," then select "clear all existing and stored DTCs."

DTC is an acronym from diagnostic trouble code.5Wait for the scan tool to confirm that the codes happen to be cleared. Disconnect the scan tool from the vehicle and start out the engine Auto diagnostics. Confirm that no MILs are illuminated within the gauge cluster. The PCM is now reset.

Car Diagnostic Tools s manual. Select &ldquo

How to Read the Check-Engine Codes on a Ford F-350 6-Liter Diesel Truck 1Locate the diagnostic connection port under the driver side dashboard. The port is roughly ½-inch tall by 2 inches wide. Remove the protective cap from the port and plug the scan tool diagnostic connector into the port.

The port resembles a multi-pin printer port for a computer system.2Follow the specific procedure in you scan tool operator’s manual for running a self test on the powertrain control module, the transmission control module and the fuel-injector control module. At each stage of the test when the codes display for each module, write the codes on your notepad, under the proper module designation. These codes correspond to specific pinpoint tests required in order to complete a full diagnosis of the problem.

3Complete the self test as specified in your scan tool operator’s manual. Select &ldquo Auto code scanner;No” when prompted to delete the codes. These codes should remain in the module’s memory. Once the problem's diagnosis and repair is complete, rerun the test and delete the codes.4Disconnect the scan tool's connector from the port under the dashboard when prompted to do so by your scan tool. Reinstall the protective cap on the diagnostic connection port Car Diagnostic Tools.

diagnostic car tool s side portion of the dashboard

Tips on how to Study OBD two Codes With a Check Engine Light 1Insert the key into the ignition.2Turn the ignition crucial for the on position and then for the off position rapidly. Typically, an precise sequence of "on-off-on-off-on" must be performed within five seconds. This will cause the "check-engine" light to blink Auto diagnostic tools.3Count the number of times the check-engine light blinks. There will be two sets of blinking. For example, if the examine engine blinks twice, this indicates "two."

There will be a pause, and then the second set will start. For example, if the second set blinks three times, this indicates "3." The proper way to read this trouble code would be "23." The "23" refers for the numbered code in your vehicle's service manual diagnostic car tool. Tips on how to Study OBD Codes on a 1999 Chevrolet S10 1Locate the OBD-II connector inside your automobile. The OBD-II connector will be on the lower driver’s side portion of the dashboard, near the emergency brake pedal. Connect your OBD-II scanner into the diagnostic port.2Close all the vehicle's doors and roll up the windows.

Turn on the scan tool and switch the ignition key to the “ON” position but do not start the vehicle.3Refer to your scan tool’s documentation for retrieving the trouble codes from your car. Write down the trouble codes displayed by the scan tool with a pen and piece of paper. Refer to the trouble code section inside the documentation that came with your scan tool or click on the resource below for a list of trouble codes for your automobile and explanations for them.4Switch the ignition back to the “OFF” position and turn off your scan tool. Remove the scan tool’s diagnostic cord from your S10’s OBD-II port.

auto diagnostic software

Tips on how to Manually Reset the Service Engine Light within a BMW 3 Series 1Put the crucial in to the ignition and turn the vehicle towards the "on" auto diagnostic software; position but do not begin the engine.

2Find the diagnostic port below the driver's side dashboard close to the pedals. Plug the computerized scan tool into this port. The battery from the vehicle will automatically energy on the tool.3Find arrows on the faceplate on the scan tool and use them to scroll via the menu until you come across the "Read All Codes" command.

Choose this command.4Scroll through the menu once again and come across "Clear All Codes Vehicle Diagnostic equipment." Pick this option then wait for the service engine light to shut off.5Turn off the vehicle and wait five minutes. Commence the engine and verify that the verify engine light continues to be off.

2012年10月11日星期四

automotive diagnostic tools

How to Install Strobe Lights 1Mark the spots where you should install your strobe lights. Set up them away from any places where they might be quickly broken, damaged or displaced.

2Drill holes automotive diagnostic tools, having a drill bit Vehicle Diagnostic equipment, in the spots exactly where you'll want to install your light. Drill holes smaller in diameter than the diameter of your screws.

3Follow the protocol offered by the strobe light manufacturer to install the strobe lights. Thread screws, provided by the strobe light manufacturer, by way of the holes within the strobe lights. Use a screwdriver to fasten the screws into the holes on the wall.

4Plug inside the strobe lights close to a surge protector or light switch.

2012年10月10日星期三

Auto diagnostics just loosen them so the dash panel comes out

The way to Hook an MT2500 to an HD2500 1Turn off the HD 2500, ensuring it really is in park along with the emergency brake is on. Unscrew the two significant, plastic screws for the underside left and suitable with the steering column. These screws are on the underside dash panel.

Leave the screws inside the dash, just loosen them so the dash panel comes out Auto diagnostics, exposing the significant cluster of wires running into a multi-plug unit Obd2 scanner.2Take the MT2500 cord-plug and align it towards the HD 2500 plug.3Push the two plugs with each other, making certain to align the rods on the MT2500 into the HD 2500 female receivers.4Turn on the MT2500 and make make certain the display screen comes on.

The way to Hook Up a Timing Light 1Lift and prop the hood when the vehicle engine is off.2Disconnect the vacuum line from the distributor and plug it with all the pencil tip. Make certain not to break the lead. Rest the pencil in a secure spot.3Grasp the red wire alligator clip on the timing light. Hook it to the positive battery terminal in the automobile.

4Locate the black wire on the timing light and attach it to the unfavorable battery terminal.5Connect the trigger clip, also known as the inductive pickup clamp, towards the initial spark plug wire. If there is an arrow on the clip, turn the clip inside the designated direction.6The timing light is now ready to make use of. Engage the help of a buddy or household member to acquire inside the automobile and begin the engine so you'll be able to use the timing light.

automotive diagnostic tool

How to Discover the Service History on a Vehicle 1Find the car's Car Identification Quantity (VIN). Come across the VIN in your car's door frame or within the engine compartment. automotive diagnostic tool

Try to find a small metal plate with all the 17-character quantity printed on it.2Go to your state's Division of Motor Vehicle's web site. Enter the VIN quantity in to the website's vehicle history database. Click "Enter" to initiate a search of the car's total service history.3Look for reports of a wreck Auto code scanner, flood damage or odometer fraud.

The report will also indicate if the car or truck was stolen or topic to a manufacturer's recall. Print the report for your records.4Contact the dealer or manufacturer for additional service data related to a recall or wreck.5Expect a longer service background for a car which has been rebuilt or salvaged from a wreck. A salvage car is deemed to have repair fees that exceed 70 percent of its pre-damage value.

Obd2 scanner or no power or ground is found on both pins

The way to Troubleshoot a 99 Ford Taurus That may be Totally Dead & Has No Power 1Set the digital volt/ohm meter for volts dc and touch the meter leads to the battery terminals ( the battery terminals are the lead portion of the battery that the cables attach to). Minimum battery voltage to test the system is 12.5 volts. If the voltage indicated on the meter is below 12.5, charge the battery before testing the system. With the battery charged, turn on the high-beam headlights and turn the heater blower motor to high speed. Retest the battery. It should maintain 12.0 volts under the load from the accessories. If the battery voltage drops below 12.0 volts with the accessories on, replace the battery.2Test the battery cable connections for a voltage drop. Touch the negative battery terminal with the negative meter lead while touching the negative battery cable with the positive meter lead. A reading of more than .1 volts on the meter indicates a bad connection. Remove the cable end, clean the connection and retest. Test both battery cable connections in this manner and clean the connections as needed. Perform the same test where the negative cable connects to the engine block.3Check for power to the starter solenoid using the automotive circuit tester. Attach the clips on the tester to the battery and touch the probe end to the terminal that the positive battery cable is attached to on the solenoid. Power should be indicated at all times.4Open the under-hood fuse block and visually inspect the 40-amp main fuse and the 10-amp starter fuse in position 20 in the fuse block. Replace any fuse found to be defective. Turn the ignition key to the run position. Touch the probe end of the circuit tester to the test pins on the 10-amp fuse. Power should be indicated on both test pins. If power is indicated on one pin, and ground is indicated on the other test pin Professional diagnositic tools, replace the fuse. If ground is found on both pins, or no power or ground is found on both pins Obd2 scanner, replace the ignition switch. Related articles:

2012年10月8日星期一

car diagnostic tool like RPM or acceleration

How you can Enable Options in Ford Computers 1Locate the OBD1 or OBD2 connection port on your vehicle. OBD2 is definitely the most recent laptop connection, and came out inside the late 1990s. It can be generally situated near the driver's side of the car diagnostics car tool, below the steering wheel.

The connection is roughly a two-inch long port with a wide cable opening.2Insert the OBD1 or OBD2 end in the cable into the connection port on your Ford vehicle. To ascertain which connection you're using, verify your owner's manual.3Insert the software package installation CD into your laptop computer system, then adhere to the prompts on the installation wizard that loads onto the screen to install the application.

The system CD is offered with all the OBD1- or OBD2-to-USB adapter cable. There are a number of unique software program titles car diagnostic tool, but all read and monitor the car within the similar way.4Plug the opposite end of your OBD1/2 cable into on the list of USB ports on the laptop.5Power on the car and launch the installed software program. The on-screen programming now displays all of the data being received by the vehicle's laptop technique. Click on the particular feature from the automobile (like RPM or acceleration) to activate the feature on the Ford laptop or computer method.

Auto tools Menu&quot

The best way to Diagnose the Check Engine Light on a 2004 Explorer Sport Trac 1Locate the onboard diagnostic access port within the driver's side footwell. This will be a 16-pin plug coming off from the primary wiring harness below the dash. The access port is located for the left in the fuse panel and is extremely visible in case you climb in to the footwell.2Plug the OBD scan tool into the access port and ensure that that it is actually secure. Auto tools

3Turn the ignition on auto diagnostic software, but don't start off the engine. Then, energy on the scan tool.4Wait for the scan tool to retrieve the codes from the Sport Trac's laptop or computer. When the tool is performed, the display should really study "OK."5Unplug the scan tool and shut off the ignition. Use the Ford Explorer Sport Trac's service manual to translate the trouble codes on the scan tool (or see Resources section). To access the codes, press "Menu" on your scan tool, and select the "Stored Codes" option on the menu screen.

Tips on how to Diagnose Electrical Problems Having a Continuity Tester in your Automobile 1Turn off the car's engine and wait for ten minutes for any electrical charge to dissipate.2Lift the hood and disconnect the red lead wire from the battery.3Access the element you need to test.4Place the alligator clip on one make contact with point on the component and touch the wire to a separate make contact with point.5Listen for any continuous buzz or watch for the tester's light electric diode, or LED, to activate. This indicates that electrical energy is flowing via the component. When you know the battery is functional and that the element will obtain a current, the problem is inside the wires major towards the component.

订阅：博文 (Atom)

Auto diagnostic tool

2012年10月30日星期二